SIMONETTO, ENRICO
SIMONETTO, ENRICO
Dipartimento di Ingegneria Industriale - DII
A new machine for testing ferrofluids lubrication performances by reciprocating sliding wear
2023 Simonetto, E.; Ghiotti, A.; Brun, M.; Bruschi, S.
Accuracy in microstructure measurements in highly directional processes
2021 Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea; Magro, Tommaso
Analysis of mechanical behaviour of AA6082-T6 sheets deformed at low temperatures
2019 Bruschi, Stefania; Bertolini, Rachele; Simonetto, Enrico; Ghiotti, Andrea
Analysis of X20Cr13 turbine blades distortions at elevated temperatures
2015 Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea; Savio, Enrico; Salvadori, Alessandro
Analytical modelling of residual stresses in sheet metal tension-levelling
2019 Magro, Tommaso; Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea; Alessandro, Ferraiuolo
Distortions of Thin-Wall Hot Forged Components in Stainless Steel
2018 Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea
Dynamic Detection of Instability Defects in tube Rotary Draw Bending
2017 Simonetto, Enrico; Ghiotti, Andrea; Bruschi, Stefania; Gemignani, Roberto
Dynamic detection of tubes wrinkling in three roll push bending
2017 Simonetto, Enrico; Ghiotti, Andrea; Bruschi, Stefania
Electroplastic effect on AA1050 aluminium alloy formability
2018 Ghiotti, Andrea; Bruschi, Stefania; Simonetto, Enrico; Gennari, Claudio; Calliari, Irene; Bariani, Paolo
Electroplastic effect on AA1050 plastic flow behavior in H24 tempered and fully annealed conditions.
2019 Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea
Enhancing the accuracy of in-process springback measurements of complex tube bending processes using cost-effective embedded sensors
2021 Ghiotti, A.; Simonetto, E.; Bruschi, S.; Savio, E.
Experimental and numerical investigation of the effect of metal surface treatments on the delamination behaviour of magnesium alloy-based Fibre Metal Laminates
2022 Liu, Z.; Simonetto, E.; Ghiotti, A.; Bruschi, S.
Feasibility of motion-capture techniques applied to tube bending
2015 Simonetto, Enrico; Ghiotti, Andrea; Bruschi, Stefania
Flexible Incremental Roller Flanging process for metal sheets profiles
2021 Simonetto, Enrico; Ghiotti, Andrea; Bruschi, Stefania; Filippi, Stefano
Formability prediction of Ti6Al4V titanium alloy sheet deformed at room temperature and 600 °C
2020 Divo Bressan, José; Wang, Qiaoling; Simonetto, Enrico; Bruschi, Stefania; Ghiotti, Andrea
High accuracy direct hot bending of hollow profiles
2021 Simonetto, E.; Ghiotti, A.; Bruschi, S.
In-line control of tube bending processes by means of smart tools
2018 Simonetto, Enrico
IN-LINE CONTROL OF TUBE BENDING PROCESSES BY MEANS OF SMART TOOLS
2018 Simonetto, Enrico
In-process measurement of springback in tube rotary draw bending
2021 Simonetto, Enrico; Ghiotti, Andrea; Bruschi, Stefania
Incremental roller-flanging of thick metal sheets
2021 Ghiotti, A.; Del Tito, B. M.; Simonetto, E.; Bruschi, S.; Filippi, S.